Skip to content
NEW Give everything another once-over, paying particular attention to your fans—it’s easy for a loose cable to drag on one, and if it does, you’ll need to open the PC up again and find the error.If you’re sure you’ve covered everything, place the access panels back on the left and right sides, and then place the thumb screws in and batten down the hatches. NEW
Gegarandeerd vele jaren gameplezier. Simply screw them down from the outside.The side of the fan with the plastic blocking the blades is the output—air flows in the direction of the plastic. There are a few screws affixing the power supply to the back of the frame. We also build gaming PC's for esports event awards and giveaway prizes. If you’re using a gaming PC, it will probably look pretty similar, unless you’re specifically building something much smaller (like a Mini-ITX build) or more elaborate.
Note that some motherboards include different types of tabs. (You’ll need the caddies that came with your new case, not the ones you removed from the old case. These are usually marked clearly on the motherboard’s PCB.As you’re routing the cables around, here and all throughout the reassembly, try to leave as few loose as you can. And honestly, you might not need to remove the fans themselves from the case if your new case already has fans attached.First, if any of your case fans were plugged into ports on the motherboard (instead of the power supply), unplug them now. Plug everything in and start up. I do, so let’s get it off of the motherboard to make the final steps of disassembly easier.First, remove the power cable that went to the power supply if you haven’t already done so.
krijg gratis extra hp, met puma 220 cvx. If not, install the ones you removed from your previous case. NEW Desktop PC's bij Coolblue: gratis bezorging & retour. These can be hard to spot, especially if you have dark screws on a dark PCB, like mine. Make sure it aligns with the exterior so that you can plug in the monitor cables.Push down firmly. NEW NEW NEW NEW These allow you to screw down the motherboard and keep its electrical contacts from shorting out on the metal of the case itself. Our gaming PC cases feature a range of styles such as windowed cases, which allow you to see inside into all of the components that make up your computer. The hard drive and SSD in my PC use this method, while the DVD drive is screwed down tight. To decide which one is right if you don’t know, Then slide the card down into the slot, putting pressure on the side nearest the rear of the case first. From basic towers that get the job done to mammoth showpieces and even tiny cases that are living-room-friendly, Scan has you covered. Cookies. Naast functionele cookies, waardoor de website goed werkt, plaatsen we analytische cookies om onze website elke dag weer een beetje beter te maken. )Now your power supply should be mostly clear.
It’s time-consuming and boring, but not particularly difficult. Just check that it’s aligned properly with you motherboard’s rear-facing ports, and push it into place from inside the case towards the outside, on the back.
Intake fans (with the plastic facing in) go on the front, output generally go on the rear, top, or bottom. Set them aside.With these major access barriers removed, you’ll have easy entry to every component.If your case has any more externally-removable parts, like dust filters, go ahead and pull these out as well.Before you begin to actually remove components, it’s best to decide on a general order. )Then plug the SATA data cables into the rear of the drives and attach them to the motherboard’s SATA drives.
Use some place without carpet if you can, to avoid static electricity.The first thing you’ll need to do to begin tearing apart your machine is to maximize your access to all the components. NEW Then lift it clear of the case and set it aside. Some automatically lock when you insert the card, some push in from the side.Now re-install the screws to permanently affix the card in place.Again, you’re just going in reverse here.
So you’ve found a sweet new case for your PC, brimming with LEDs and fan cutouts and acrylic windows all over.
It may take a little gentle wiggling get the ports on the back of the board pushed into their respective holes in the I/O plate—just go gently and make sure you have clean access to all the ports on the rear of the computer.Now screw down the motherboard screws in the same spots you placed the risers. It’s built into a Fractal Design R4 case, a fairly typical ATX Mid Tower size. Take these out and set them aside.Then simply slide the access panels towards the back of the machine and pull them off. Do things in whatever order feels best to you.To begin removing the PSU, you’ll need to unplug it from all the components that are using it.